How To Remove A Car Stereo From A Toyota

Toyota got a smart review among the car models. Over the years, the most popular automakers

produced different kinds of autos (trucks, SUVs etc). Each configuration cars have different kind of stereo system. As like others Toyota also got different manufactures.

Things you will need

• 10 mm wrench
• key 10mm and drive

Step-1:

Lift the Toyota's hood and now needs to disconnect grounding cable. It needs to disconnect from the negative battery terminal with the 10 mm wrench.

Step-2:

From the dashboard, pull out the ashtray carefully. Now, claim the bottom of the plastic trim panel surrounding the control buttons and stereo plant, and haul the plank from the board.

Step-3:

Remove the screws 10 mm bolt from the corners of the stereo bracket with 10mm key and car.

Step-4:

Pull the factory stereo from the stereo mounting dock to access the wiring connected to the back of the stereo. Pull the stereo cables from the back of the stereo to completely free the unit from Toyota.

How Do I Change The Rear Speakers In a 2005 Hyundai Elantra

2005 Elantra Hyundai was correctly decorated with four entertainment system speakers, settled a single car speaker and the both two onward (font) doors with the other speakers are hidden below the rear parcel. Although these speakers was the best & powerful model across the market, they made quite well for most Elantra owners. Replacing rear speaker calls for removing the rear seat and several trims, such as rack pack. Although it can seem much harder at first view, the project can be easily completed by most of the owners.

Things you will need:

• Socket
• Ratchet that
• Flat screw-driver
• Phillips screw-driver
• TRIMs stick

Step-1:

At beginning unscrew the 2 screws at the back of the rear hard seat in the cabin of the Elantra, which is finely located among the backrest and seat cushion, using a ratchet and reception. Pull back the pad and rotate it toward the front of the Elantra to the hooks under the front part of the pillow disengage from their owners. Remove the seat cushion from the cabin of the Elantra.

Step-2:

Pass the rear seat center belt shoulder belt by the driver which will be at the top of rear seat. You have to lower back as far as you can, then remove the screws from the hinges carefully using a ratchet and socket. Carefully Remove backrest from the cabin of the Elantra.

Step-3:

Unbolt the lower part of the three rear shoulder webbing belt from the bottom part of the cabin Elantra.

Step-4:

Pull out the clips which securing the rear package trim panel very carefully and the trim panel is located behind the rear seat backrest, in the trunk, using a flat screwdriver. Unscrew the two screws using tools. Last of all remove the back lining package.


Step-5:

Exit the cabin Elantra and you have to open the trunk lid carefully. By locating the center brake light support the housing tabs at the bottom of the rear shelf package.

Step-6:

The climb back into the cabin, and then pull the brake light housing center and towards the front of the Elantra to be free. Unplug the brake light. I look at the back panel shelf package off the shelf rear panel, using a trim stick. Pull the cover forward and slip the straps of the seat belt out of the passage openings in the sides and in the center of the table.

Step-7:

Remove the four screws that secure the rear speakers to the left and right sides of the rear rack frame, using a Phillips screwdriver. Lift the speaker from the recess, then disconnect the connectors from the speaker terminals. Repeat to remove the remaining speakers, if necessary.

Step-8:

Plug connections of the terminals of the new speaker. Lower the speaker into the jack and tighten the four screws until tight. Place the remaining speakers, if necessary.

Step-9:

The following offer rear seat belt shoulder straps through the openings on the sides and in the center of the rear panel shelf package. Place the monitor on the back shelf and push down firmly until the panel mounting clips snap into place. Connect the brake light in the center slot, slip then the brake light tabs through the slots cut in the table until it clicks into place.

Step-10:

Re-install the upgrade package back panel lining around the trunk compartment opening. Push the clip ends of the table in their respective holes in the trim panel, then tighten the two screws in place on the bottom of the panel, using a Phillips screwdriver.

Step-11:

Align the hinges on the lower corners of the back seat with their counterparts on the floor of the cabin. Screw the hinge bolts in place, using a ratchet and socket. Raise the backrest in a fully raised position.

Step-12:

The center seat belt shoulder strap collar over the end of the belt and press it into place in the center of the rear rack pack until it clicks into place. Pull the seatbelt straps over the back. Screw back straps shoulder seat belt to the floor of the cabin, using a ratchet and socket. Slide center seat belt in the belt guide at the back center.

Step-13:

Push the rear pillar trims in the country. 

The 15 offer below the hooks on the front of the rear seat cushion during the catch on the floor of the cabin. Lower the back of the seat in the back. Pull the belt buckles out from between the back and the cushion, then press the pad firmly in place. Screw the two screws with the pad straps to secure it to the floor of the cabin, using a ratchet and socket.

To know more about best car speakers visit Speaker Champion

How You Can Install a Car Antenna Cable Easily

The first thing many people do in their car is they installs a new car stereo if they needs, mainly to
increase enjoyment many people do it to get the best feelings of melodies. The most critical elements for the stereo is a fixed antenna, because without a fixed antenna, you can't listen to the radio. If your antenna is broken down or the cable is not properly connected. You should replace the entire antenna properly. This is not a difficult part to do. But it will take some time to fix it properly, and you must needs to use some special tools to fix. 

The things that will need to fix all those:

 

• Replacement Antenna
• Screwdriver
• Wire Cutters
• 1/4-inch Ratchet, Extension and Sockets
• Removal Antenna tool
• and much more

#1
1st of all remove the antenna from the wing using a removal tool antenna. The tool will loosen the nut of the antenna and will allow you to throw the antenna base from the bottom of the wing.

#2
Now, open the hood and locate the grommet in the firewall of the passenger side that the antenna cable goes fine. Push out the hole with the screwdriver to pop the rubber of the outer ring around the sides. Then cut the antenna lead using wire cutters and pull the rest of the antenna line outside the ring hole in the engine compartment using your hands.

#3

Bolt replacement antenna on the wing using the antenna tool, and then run the wire antenna inside the wing and inside the firewall, pressing the ring in place, and finishing the engine bay portion of the installation. good quality 4 Place your foot on the brake and shift the truck at a low speed. Then pull the bezel surrounding the radio and the meter panel with your hands. With slight pressure, the hoop dashboard will Release the backboard.

#5
Unbolt the stereo from the dashboard using the 1/4-inch ratchet, extension and sockets. Then pull out and disconnect the stereo wiring and antenna from the back of the board with your hands.

#6
Lean under the instrument panel and pull out the old antenna from the board with your hands. Then run the new antenna cable from the board with your hands to work the antenna leaves the board. This could mean opening the front passenger glove compartment and moving the cable through the dashboard.

#7

Connect the wiring for the stereo behind the back of the deck and connect the new antenna cable to the rear of the deck as well. Then screw the stereo behind the dashboard using the 1/4-inch ratchet, and clip the rear dashboard bezel into place in the reverse order of installation.

How to connect a Sub to a stereo factory on Your Car

Adding bass in a car factory audio system, there's no easier or more effective way than to add a sub-woofer. A sub-woofer is gonna provide the low-end punch that makes sound more clear and regardless of the type of music you listen to. It's the most working & effective way ever. If you like you can have a technician to do the installation, or you can connect your own and save the cost of labor(s).

Things you will need:

• Phillips-screwdriver
• Amplifier wiring kit
• Investing Tool
• Amplifier
• The Show More Instructions

 

How to wire a Sub to a stereo factory:

#1
Disconnect the negative battery cable from the vehicle battery. The negative cable is called a black cable. Connecting it (the negative cable) the car battery to the frame of the vehicle. Use a normal screwdriver to loose the pin and finally you will be able to remove the clamp from the negative(-) line.

#2
Now you should remove the stereo from the panel (dashboard). They should have the access to each connections on the back of each unit.Then it will be perfect enough for next step.

#3
At this step place the sub-woofer & amplifier in the trunk of the your car. The amplifier can be placed at other areas (such as under the seat). But the body should have an easier connection to the sub-woofers. Those things you have to focus to get the most amazing result that you are accepting.

#4
Connecting the ring terminal, it should give you the best positive result of the battery. And you must ensure that the security has been removed from the terminal. And that should be done before connecting the power cord into the terminal ring.

#5
Then route the power cord from the amplifier ring terminal. Now you have use a grooming tool to remove the coating that ensures the carpeting in the vehicle floor. The panels you can easily replace.

#6
And now route the signal cable and must enable to lead from the stereo of the trunk along the opposite side of the vehicle. The power cable will make problem if  the signal cables are in the same line.

#7
Now connect all those (power cable, signal cable) and now it's time to turn-on lead to the amplifier.

#8
Now, using speaker cable Connect the sub-woofer.

#9
Now you have to connect the negative (-) battery cable. Place the clamp around the negative (-) lead. Tight the bolt on the clamp until the clamp can not be moved to the lead by your hand.


That's all about How to connect a Sub to a stereo factory. Hope you got this article valuable & hope it gave you a bit knowledge about the issue you were getting.